ridgeway grandfather clock serial number lookup

Is the auto night selector on daytime? This question is for clocks equipped with ANSO (auto night shut off) where the clock is designed to not play any music between 10pm and 7am. Sometimes what people do if this is the situation is they get a brass rod and bend it to attach to this arm and let it run down the back of the dial so someone can turn the chimes on or off by the end of the rod.Ģ. If you have the type of dial with no selector slot, you will have to get to that side of the movement from the back and see if there is an arm sticking out of the side of the movement that you can raise or lower. Usually this will have an arm coming out of the dial so you can select it up or down, but then some dials are not equipped with the slot for this arm to come through. Is the chime selector on chime? There is a switch on the 3 o’clock position on the clock movement. On some movements it is between the hand shaft and the 3 o'clock selection switch in the middle of the dial.ġ. If there is an ANSO feature on the clock movement the switch would usually be on the left when facing the clock at 9 o'clock. Solution is to go around 12 hours with the clock hands. This being a mechanical clock, it has no sensors to determine on its own what is night or day. If the clock does not chime it will not strike, so therefore the clock remains silent. It is possible that it thinks it's night when it's really day, and therefore will not chime. This stands for Automatic night shut off, and the intention is to have the clock be silent automatically from 10pm to 7am (usually). Higher end mechanical clock movements sometimes include an ANSO feature. So if the chain or cable is rubbing something it's the same as not having the right amount of weight on the clock. Resistance is what makes a clock stop because there is not enough weight to drive through whatever is rubbing. If the cable or chain is rubbing something it will cause resistance. They should be straight from the ratchet wheel or cable drum and straight down to the clock weight with nothing rubbing. In other words, the chains or cables do not rub the seat board, pinch or wrap around the movement pillar, or anything like this. Check the cables or chains that they are not rubbing anything on their way down to the weight. This is the chime side of the clock and requires the heaviest weight of them all. Weights, cables, or chains not rightĬonfirm the heaviest weight is on the right while facing the clock. Changing the chime song when the current song is in midstream can cause this same issue. Shipping may cause the roll pin to jam up like this. This will release a jam in the chime roll pin and let it bounce into position. To correct this pull all the chime side hammers back all at once and then let go. When the clock selector switch is on chime and still does not work, the next thing to check is a jam in the roll pin. If it's a Westminster only unit, UP is off and DOWN is chime. So if there is no switch then this cannot be the reason for no chimes. Not all movements have the silence switch. If this is the situation access it from the back of the clock instead. The movement may have this switch but the dial may not have a slot to get at it on some Westminster only units. If the clock is a triple chime movement, meaning it has three songs, it will have the song selection and also silent on this switch. There may be a switch at the 3 o'clock and this switch turns the chimes on or off. If the minute hand goes all the way around for an hour with no chime, continue to the next section. If it does not chime go forward to the next and the next quarter. A faint click can be heard and at that point pause and see if it starts chiming. Go forward with the minute hand with fingers while going slow past the quarters. Could be looking for the top of the hourįirst thing to do is see if it chimes after 3/4 of an hour. This is because the clock is looking for the top of the hour so it does not lose its place as to when to chime. Please note that post WW2 German mechanical clocks are designed so that if turning the hands fast or stop the clock for a long while it may not chime for up to 3/4 of an hour. In other words what falls into the realm of being a set up issue instead of a movement issue. This section will resolve chime issues that are not the fault of the clock movement itself. The strike is what calls out the hours after it is done with the chime song. The chime is the song that plays every 15 minutes and not to be confused with the strike.

When a grandfather clock has issues with the chime functioning these are some basic corrections.

Leave us a comment, or start a discussion.

Could be looking for the top of the hour.

Ridgeway grandfather clock serial number lookup